- The Complete Research Material is averagely 52 pages long and it is in Ms Word Format, it has 1-5 Chapters.
- Major Attributes are Abstract, All Chapters, Figures, Appendix, References.
- Study Level: BTech, BSc, BEng, BA, HND, ND or NCE.
- Full Access Fee: ₦6,000
Get the complete project »
Also studies were he manner of dependence of these parameters on prints impressed on sheets of varied thickness. The results of these investigation were utizlied in the design and fabrication of an operational manual printing machine using gold foil sheet depositor clear prints were impressed on papers during the new machine’s operation.
TABLE 1 - Experimental determination of pressure for printing
11- Effect of temperature on sharpness of print.
111 – Description of (components) parts and materials use for them
1v- comparison of cost and properties of materials
LIST OF FIGURES
Description
Figure 1 sketch of alternative A
Figure 2. Sketch of alternative B.
Figure 3 sketch of alternative C
Figure 4 isomeric view of hot plate square housing
Figure 5 isometric view of type holder
Figure 6 &7 load and free body diagram of crank are (Handle) and rod.
LIST OF SYMBOLS
A – Area
A – Acceleration
D – Maximum shaft diameter
d- minimum shaft diameter
e- efficiency
k – Thermal conductivity
c – Heat capacity
x – The pressure transmissibility of lever system (press x 1/duration )
t – Time
l – Length of shaft
m – Mass
m – Maximum bearding moment
p - Electric power
q – Quantity of heat
Letter of transmittal iii
Release iv
Approval page v
Dedication vi
Acknowledgement vii
Abstract viii
List of figures ix
List of tables x
List of symbols xi
Table of contents xii
CHAPTER ONE
1.1 introduction 1
1.2 literature review and data collection 2
1.3 experimental determination of pressure for prating 3
1.4 design specification 9
CHAPTER TWO
2.1 Design solutions 11
2.2 Alternative A press foot printer 11
2.3 Alternative B; crank arm (handle ) 14
2.4 Alternative C; automatic (motorized) printer 17
2.5 Comparison of alternative and choice 20
CHAPTER THREE
3.1 Design selection and analysis of parts of chosen alternative 22
3.2 Theory of design/ design calculation 24
3.3 The design of the shaft (Hollow) 26
CHAPTER FOUR
4.1 construction of prototype 28
4.2 general 28
4.3 material selection 29
4.4 sequence of construction and assembly 40
CHAPTER FIVE
5.1 Testing of prototype (test – run) 40
5.2 Evaluation of machine efficiency 40
5.3 Operator’s manual 41
5.4 Costing (cost analysis) 42
5.5 Problems Encounter 45
5.6 Conclusion 45
5.7 Recommendation 46
Reference 48
You either get what you want or your money back. T&C Apply
You can find more project topics easily, just search
-
SIMILAR MECHANICAL ENGINEERING FINAL YEAR PROJECT RESEARCH TOPICS
-
1. DESIGN AND FABRICATION OF WOOD LATHE MACHINE
» CHAPTER ONE 1.0 INTRODUCTION The wood lathe machine is introduced to lessen the human suffering and to improve economical and technological standard, ...Continue Reading »Item Type & Format: Project Material - Ms Word | 49 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
2. CONSTRUCTION OF A DOUBLE BUNK BED
» ABSTRACT This project is based on the construction of a double bunk bed which will serve a great place for resting and sleeping. It is done with avail...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
3. CONSTRUCTION OF OFFICE TABLE
» ABSTRACT Furniture refers to movable objects intended to support various human activities such as sitting for chairs, Stools and Sofas, eating and rea...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
4. MULTIDISCIPLINARY DESIGN OPTIMIZATION OF AN AIRCRAFT WING (AERODYNAMICS & STRUCTURAL)
» ABSTRACT The quest to operate at the cutting edge of technology is a worthwhile effort but requires intensive research and brilliant implementation of...Continue Reading »Item Type & Format: Project Material - Ms Word | 98 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
5. DESIGN, SIMULATION, CONSTRUCTION AND PERFORMANCE EVALUATION OF A SOLAR BOX COOKER
» ABSTRACT A solarbox cooker is a device that converts solar energy into useful heat in a confined space. The solar cooking system which captures and ut...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
6. DESIGN AND CONSTRUCTION OF JOURNAL BEARING DEMONSTRATION RIG
» ABSTRACTThe journal bearing demonstration rig is an apparatus which is used to study how pressure would vary around the section of a journal bearing a...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
7. DESIGN AND CONSTRUCTION OF PUNCH AND DIE FOR PRODUCTION OF CUPS LETTER OF TRANSMITTAL
» CHAPTER ONE 1.0 INTRODUCTION In recent years, Nigeria lays strong emphasis on the manufacturing of both industrial and household products within the c...Continue Reading »Item Type & Format: Project Material - Ms Word | 35 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
8. SKILL IMPROVEMENT NEEDS OF METAL WORK TECHNOLOGY TEACHERS IN TECHNICAL COLLEGES IN KADUNA STATE
» TABLE OF CONTENTS Title page i Approval page ii Declaration iii Acknowledgement iv Table of contents v Abstract vi CHAPTER ONE: INTRODUCTION Backgroun...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
9. CEMENT MANUFACTURING /PRODUCTION IN NIGERIA. A CASE STUDY OF EDO CEMENT FACTORY, UKPILLA, EDO STATE.
» ABSTRACT The project studied the manufacture of cement production in Nigeria using Ukpilla as a case study. It enables us to compare the differences b...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT
-
10. INVESTIGATION OF THE EFFECT OF MOULDING SAND (NATURAL & SYNTHETIC) ON CASTING OF FLANGE USING ALUMINIUM
» ABSTRACTThis study tend to investigate the effect of synthetic and natural moulding sand on casting of flange like component. In this study FUTA logo ...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | MECHANICAL ENGINEERING DEPARTMENT