- The Complete Research Material is averagely 84 pages long and it is in Ms Word Format, it has 1-5 Chapters.
- Major Attributes are Abstract, All Chapters, Figures, Appendix, References.
- Study Level: BTech, BSc, BEng, BA, HND, ND or NCE.
- Full Access Fee: ₦6,000
Get the complete project »
CHAPTER ONE
INTRODUCTION
1.1 OBJECTIVE OF PROJECT
The need for a remote control alert system that can control domestic appliances and various lighting points and sockets has often been a concern for users. At times users find it inconvenient and time consuming to go around turning their appliances on or off each time there is power outage or each time they are leaving the house for work. It has also often led to damage of appliances due to the fact that an appliance was not turned off before leaving the house.
The Objective of putting up this project, therefore, is to design an equipment that can facilitate a convenient and easy way of controlling our domestic appliances, lighting points and sockets especially in powering them, without always going to appliances physically by ourselves.
This objective will be accomplished using various components which include a Microcontroller (AT89C51) which acts as the backbone of the project together with other components.
1.2 JUSTIFICATION OF PROJECT
The ease of putting our appliances, lighting points and sockets on or off has made it necessary to develop this system in order to control our appliances, lighting points and sockets from a central point using a remote control. The issues of always forgetting our appliances ON when leaving the house has often caused fire outbreak and explosion in homes and this is another reason that led to designing and construction of this project.
1.3 SCOPE OF DIAGRAMS IN PROJECT
In this project report, the diagrams will range from simple block diagrams to complex circuit diagrams which will comprise mostly of common electrical and electronics symbols. Some of the diagrams that will feature in this report will be used as the main block on which certain parameters will be explained upon. Relevant electronic components will also be shown and described.
This project report will also contain an outline of the circuit diagram as it is seen physically. The package design diagram will be included showing the width, height in millimeter (mm).
1.4 BLOCK DIAGRAM OF PROJECT
Fig 1.0: Block diagram
1.5 PROJECT REPORT ORGANIZATION
Chapter 1 serves as the introductory chapter where I try to relay the concept and acceptable reasons why the project should be implemented for the intending user of the work. Thus, showing the block diagram of the design and a scope of diagram for the entire project design.
Chapter 2 deals with the literature review where it will be discussing the origin of this project design. In the origin of the project, we will be looking at what brings about the three phase selector in our day to day activity and how the idea of designing this project comes about.
A description of the Project is also given where the 2 sections of the project are discussed and the various components contained in the sections also mentioned.
The use and importance of this project design will also be mentioned here. It will be looking at the best place where this project design can be use and where it cannot. This chapter will also make room for adding additional information that will help in the actualization of this project design.
Chapter 3 treats the methodology of this project design. It comprises of the information gathering; the source of the materials used in designing and writing the project report, data analysis; the components and devices used in the course of designing this project will be analysis to know their basic means of operation and how they will help in putting up this design, system design approach; the possible way to tackled the project design from scratch, bottom-up; it will treat how the practical detail was gotten before considering about the general principle of the system design, choice of design system; it focuses on why the project design was done using a microcontroller rather than using only digital logic, and also the data flow arrangement and system flow chart.
In chapter 4, the detail design work will be presented. It will include the schematic of the design of the various sections of the design and the source code (in C language) used in programming the microcontroller.
Chapter 5 will be discussing the system testing, Expected results, and Performance evaluation.
Summary and conclusion of the design will be presented in Chapter 6. It will be looking at the problems encountered in designing the project and possible solutions to them. From the problems and solutions of this work, the suggestion for further improvement will be stated.
You either get what you want or your money back. T&C Apply
You can find more project topics easily, just search
-
SIMILAR ELECTRICAL ENGINEERING FINAL YEAR PROJECT RESEARCH TOPICS
-
1. CONSTRUCTION OF RADIO FREQUENCY GSM SIGNAL JAMMER
» CHAPTER ONE INTRODUCTION 1.1 Introduction A wireless signal jammer is a device which blocks transmission by creating interference. This wireless signa...Continue Reading »Item Type & Format: Project Material - Ms Word | 50 pages | Instant Download | Chapter 1-5 | ELECTRICAL ENGINEERING DEPARTMENT
-
2. THE DESIGN AND CONSTRUCTION OF FM RADIO TRANSMITTER
» ABSTRACT An FM transmitter is an electronic device which, with the aid of an antenna, produces radio waves. The transmitter itself generates a radio f...Continue Reading »Item Type & Format: Project Material - Ms Word | 43 pages | Instant Download | Chapter 1-5 | ELECTRICAL ENGINEERING DEPARTMENT
-
3. DESIGN AND CONSTRUCT AN INTELLIGENT TRAFFIC LIGHT CONTROL SYSTEM USING SENSORS AND A MICROCONTROLLER
» CHAPTER ONE 1.0 INTRODUCTION Traffic control systems include signs, light and other devices that communicate with specific direction, warning, or requ...Continue Reading »Item Type & Format: Project Material - Ms Word | 52 pages | Instant Download | Chapter 1-5 | ELECTRICAL ENGINEERING DEPARTMENT
-
4. MODELLING AND OPTIMIZATION OF A HYBRID ENERGY SYSTEM FOR GSM BASE TRANSCEIVER STATION SITES IN EMERGING CITIES
» CHAPTER ONE INTRODUCTION 1.1 Background to the Study The history of the Nigerian Telecommunication Industry can be divided into three phases (Okere, 2...Continue Reading »Item Type & Format: Project Material - Ms Word | 333 pages | Instant Download | Chapter 1-5 | ELECTRICAL ENGINEERING DEPARTMENT
-
5. DESIGN AND INSTALLATION OF 200 WATT SOLAR POWER SYSTEM
» CHAPTER ONE INTRODUCTION 1.1 NEED FOR THE PROJECT The general objective of the system is to provide efficiency, steadiness in the use of power applian...Continue Reading »Item Type & Format: Project Material - Ms Word | 41 pages | Instant Download | Chapter 1-5 | ELECTRICAL ENGINEERING DEPARTMENT
-
6. REMOTE PATIENT MONITORING SYSTEM
» ABSTRACT This thesis has to do with the transfer of medical records taken remotely to a doctor via GSM wireless communication link. Specifically it ma...Continue Reading »Item Type & Format: Project Material - Ms Word | 170 pages | Instant Download | Chapter 1-5 | ELECTRICAL ENGINEERING DEPARTMENT
-
7. DESIGN AND CONSTRUCTION OF 12V BATTERY CHARGER
» CHAPTER ONE INTRODUCTION 1.1 Background of Study Few modern electrical appliances receive their power directly from the Utility grid like National Ele...Continue Reading »Item Type & Format: Project Material - Ms Word | 53 pages | Instant Download | Chapter 1-5 | ELECTRICAL ENGINEERING DEPARTMENT
-
8. THE CONSTRUCTION OF ELECTRONIC DISPLAY BOARD
» CHAPTER ONE 1.0 INTRODUCTION The purpose of this project is to produce a narrative description of the design and construction of an electronic display...Continue Reading »Item Type & Format: Project Material - Ms Word | 38 pages | Instant Download | Chapter 1-5 | ELECTRICAL ENGINEERING DEPARTMENT
-
9. DESIGN AND CONSTRUCTION OF AUTOMATIC CHANGEOVER SWITCH WITH INDICATOR
» CHAPTER ONE INTRODUCTION Industrial automation and control has contributed immensely to the high rate of the world’s technological growth. Power...Continue Reading »Item Type & Format: Project Material - Ms Word | 48 pages | Instant Download | Chapter 1-5 | ELECTRICAL ENGINEERING DEPARTMENT
-
10. CONSTRUCTION OF A FREQUENCY TO VOLTAGE CONVERTER
» ABSTRACT The project is aimed at constructing a frequency to voltage transducer circuit. The method of constructing this circuit is first simulated on...Continue Reading »Item Type & Format: Project Material - Ms Word | 23 pages | Instant Download | Chapter 1-5 | ELECTRICAL ENGINEERING DEPARTMENT